Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Cap & Crown in Joliet: What to Know First
We provide independent Olympia Chimney chimney cap and crown service in Joliet, with most repairs completed in a single booked visit and pricing delivered in writing before any work starts. A standard Olympia Chimney cap replacement runs $280-$520; crown repair or coating typically falls between $340-$780 depending on accessibility and the extent of masonry deterioration. Every job includes our NFPA 211 Level 2 camera inspection and a documented photo record under Haven Standard Clause 4.
This page is for Joliet homeowners who’ve found Olympia Chimney hardware on their flue, aren’t sure if it’s still doing its job, and want the price before someone climbs their roof. Call (815) 620-5234 - a live person answers, 24/7.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney stainless single-flue caps (SC-series): The SC-913 and SC-1117 are common on Joliet’s 1950s-1970s ranches in neighborhoods like Cathedral Area and near Pilcher Park. The 304-grade mesh on earlier production runs fatigues at the weld points after 8-12 winters of freeze-thaw cycling. We see the screen detach completely while the lid still looks fine from the ground. Our fix: match the flue dimension precisely, and if the original was 304-grade, we quote 316-grade replacement with a lifetime-weld guarantee through our Haven buying network.
- Olympia Chimney multi-flue caps (MC-series): The MC-1317 and MC-1721 carry a lot of surface area, and on Joliet’s older two-flats near the Iron Works Historic Site, we find the mounting struts have pulled away from the crown. The real cause isn’t the cap - it’s spalling concrete underneath that let water infiltrate, freeze, and lever the anchors loose. We remove the cap, photograph the crown condition with the camera, then repair the masonry substrate before remounting. Installing a new cap on a failed crown is Clause 1 violation: work without a written scope of what’s actually broken.
- Olympia Chimney galvanized economy line: These were stocked by several Joliet-area builders during the 2004-2012 construction wave. The galvanized coating fails at the drip edge first, showing orange streaking on the brick below that homeowners mistake for roof runoff. By the time the rust reaches the mesh, the underlying metal is thinned to foil. We don’t coat or patch these - we replace with stainless or copper, and we show the customer the thickness gauge difference in the photo record.
- Olympia Chimney wind-directional caps (WD-series): The WD-913’s rotating hood seizes after debris accumulation, common in Joliet where cottonwood fluff from the Des Plaines River corridor packs the bearing race every June. A seized WD cap is worse than no cap: it blocks draft and traps moisture. We disassemble, clean the race, and if the bearing is pitted, we source a replacement rotating assembly or convert to a static high-vent cap if the customer prefers zero maintenance.
- Olympia Chimney crown wash failures beneath their caps: This is the failure Olympia Chimney’s own documentation understates. Their installation manuals specify a 2-inch minimum crown overhang, but in Joliet’s clay-heavy soil zone, chimney settlement often cracks that overhang within five years. Water gets behind the cap flange, rusts the mounting hardware, and the cap loosens without the owner noticing. Our camera inspection catches this from inside the flue - water staining on the liner above the smoke shelf is the tell - and we repair the crown with proper slope and drip edge before resetting or replacing the cap.
Our Olympia Chimney Chimney Cap & Crown Process
- 1
Call and schedule. A live person answers, notes your Olympia Chimney model if you know it, and books a window. You get a text when your tech is en route.
- 2
Level 2 inspection on arrival. Camera down the flue, photos of the cap and crown from the roof, documented readings. Corrine Halstead puts the inspection photos in front of you before discussing price. The photo doesn’t argue. It just shows you what’s there.
- 3
Written scope and price. We specify OEM Olympia Chimney parts versus quality aftermarket alternatives (often Gelco or Famco equivalents through our buying network), with the price difference stated plainly. No work starts until you have this in writing - Haven Standard Clause 1.
- 4
Repair or replacement. Crown repair uses proper Portland-based mix with acrylic fortifier, sloped 3/4 inch per foot minimum. Cap installations get sealed with high-temp silicone at the flue interface, never just gravity-seated.
- 5
Post-work test and documentation. We run a draft test, verify cap clearance, and upload your photo record. You get the written warranty before we leave - 365-Day Done Right Promise, stamped and dated.
- 6
Cleanup and follow-up. Magnetic drop cloth, debris removed, and a call within 48 hours to confirm satisfaction.
Before
AfterWhat Olympia Chimney Chimney Cap & Crown Costs in Joliet
| Service | Typical Range | What Moves Price |
|---|---|---|
| Olympia Chimney single-flue cap replacement | $280-$420 | Flue size, mesh grade (304 vs. 316), roof pitch |
| Olympia Chimney multi-flue cap replacement | $480-$780 | Span width, mounting condition, custom screening |
| Crown repair (spalling, minor cracking) | $340-$580 | Linear feet of damage, accessibility, need for forming |
| Crown coating (sound substrate) | $380-$520 | Surface area, number of flues, primer required |
| Crown rebuild (structural failure) | $1,200-$2,400 | Dimensions, reinforcement, cap reset included |
These are 2024-2025 Joliet market ranges based on our actual booked jobs. We don’t estimate over the phone without seeing the crown condition - but we don’t charge for the inspection that produces your written price, either. Call (815) 620-5234 for a free estimate.
Why Joliet Homeowners Call Level Two Chimney Joliet for Olympia Chimney Work
We’ve inspected over 38,000 chimneys since 2009, and a significant share of the Joliet inventory runs Olympia Chimney hardware from the 2000s building boom. Our techs know the difference between an SC-series and an MC-series without climbing down to check the stamp - the mounting pattern and mesh density are distinct. When Olympia Chimney parts are back-ordered, we have qualified alternatives through DuraFlex, HeatShield, and Gelco in our Haven buying network, and we explain the trade-off in writing before substituting.
Every job carries the 365-Day Done Right Promise: if it’s not done right, we make it right. No voicemail loops, no pricing games, no work without a written scope. Background-checked, uniformed technicians. License number on every page. And if you have a competitor’s written estimate, we’ll give you a free second opinion - Haven Standard practice since we opened.
FAQs
No - but only if the work is done with compatible parts and proper methods. As an independent Olympia Chimney service provider, we’re not affiliated with the manufacturer, and their original warranty on materials has likely expired if your cap is more than 5-7 years old. Our 365-Day Done Right Promise covers our labor and the parts we install. We document everything so there’s no dispute about what was done.
Most single-flue replacements are completed in 90 minutes to two hours, including the Level 2 inspection. Multi-flue caps or jobs requiring crown repair first can run half a day. We book specific windows, not “sometime Tuesday,” and we text when we’re on the way.
We source both. OEM Olympia Chimney caps are available through our Haven buying network, but delivery can run 10-14 days. For customers who need faster turnaround, we stock Gelco and Famco equivalents that match Olympia Chimney dimensions and often exceed the original gauge. We put both options in your written quote with the price difference stated - you choose before we order.
Pull the cap and look for cracking, spalling, or pooling water on the crown surface - but we don’t recommend homeowners climb their own roof. Our camera inspection reveals crown condition from inside the flue: water streaks, mortar debris, or daylight at the flue joint all indicate crown failure. Nothing is recommended without photo evidence you can see yourself. Call (815) 620-5234 for a free estimate.
Water enters the flue, degrades the liner, and in Joliet’s freeze-thaw climate, accelerates masonry damage through the winter. A failed cap also admits animals, debris, and downdrafts that can force carbon monoxide into living space. The repair cost compounds: a $340 cap replacement ignored becomes a $2,000+ crown rebuild and potential liner damage. We show you exactly where you are on that timeline - no scare tactics, just the photo record. Call (815) 620-5234 and we’ll put a date on it.
Written by Corrine Halstead, Owner, Level Two Chimney Joliet at Level Two Chimney Joliet, serving Joliet and nearby areas.